IP settings on the computer
To see the ip on Linux
Making an IP address can be done such as the following example
# ifconfig eth0 192.168.1.1 up
View information that will form with the following example
# ifconfig eth0
eth0 Link encap: Ethernet HWaddr 00:30:84:9 E: E4: 53
inet addr: 192.168.1.1 Bcast: 192.168.1.255 Mask: 255.255.255.0
UP Broadcast Running multicast MTU: 1500 Metric: 1
It to the IP address in Windows XP do the following:
1. In the Run command (Windows + R), type control panel
2. Select the icon and click the Network Connection
3. Right-click on Local Area Network and select Properties
4. Select Internet Protocol (TCP / IP) and select Properties
5. Select the radio Use the following IP Address
6. the content of your IP address
7. Select ok and so on
Tests
To test whether IP do you have for running well, do peritah ping:
Response ping successful:
root ~ root # ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56 (84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq = 1 TTL = 64 time = 0147 ms
64 bytes from 192.168.1.1: icmp_seq = 2 TTL = 64 time = 0119 ms
64 bytes from 192.168.1.1: icmp_seq = 3 TTL = 64 time = 0120 ms
64 bytes from 192.168.1.1: icmp_seq = 4 TTL = 64 time = 0195 ms
64 bytes from 192.168.1.1: icmp_seq = 5 TTL = 64 time = 0126 ms
--- 192.168.1.1 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 3996ms rtt min / avg / max / mdev = 0.119/0.141/0.195/0.030 ms
Naming fails if the ping does not show repon as above, one of the examples:
root ~ root # ping 192.168.1.4
PING 192.168.1.4 (192.168.1.4) 56 (84) bytes of data.
From 192.168.1.1 icmp_seq = 1 Destination Host Unreachable From 192.168.1.1 icmp_seq = 2 Destination Host Unreachable From 192.168.1.1 icmp_seq = 3 Destination Host Unreachable
--- 192.168.1.4 ping statistics ---
5 packets transmitted, 0 received, +3 errors, 100% packet loss, time 4026ms
, Pipe 3
You can ping to the IP network your colleagues to see if there is a connection between your PC to your PC network partners.
Penyetingan UTP cable with RJ 45 connectors
There are eight small cables in cable UTP but needed only four cable only. There are differences in the two cables to connect to a computer without a hub / switch, two-way computer dihubgunkan with crosslink as show in the picture below:
If refers to the color of the cable, you can use a table barikut:
Color cable PIN PIN
1 Orange + White 3
2 People 6
3 White + 1 green
4 Blue 4
5 White + 5 blue
6 Green 2
7 White, Brown 7
8 Brown 8
to cross pc to pc
but when we use the pc to the hub setingn cable that is in use.
Color cable PIN PIN
1 White 1 Orange +
2 People 2
3 White + green 3
4 Blue 4
5 White + 5 blue
6 Green 6
7 White, Brown 7
8 Brown 8
To test whether the relationship between the PC in the network, you can use the IP ping command the network. Usually, the success of the cable can be also seen from the light on the HUB or landcard up.
To see the ip on Linux
Making an IP address can be done such as the following example
# ifconfig eth0 192.168.1.1 up
View information that will form with the following example
# ifconfig eth0
eth0 Link encap: Ethernet HWaddr 00:30:84:9 E: E4: 53
inet addr: 192.168.1.1 Bcast: 192.168.1.255 Mask: 255.255.255.0
UP Broadcast Running multicast MTU: 1500 Metric: 1
It to the IP address in Windows XP do the following:
1. In the Run command (Windows + R), type control panel
2. Select the icon and click the Network Connection
3. Right-click on Local Area Network and select Properties
4. Select Internet Protocol (TCP / IP) and select Properties
5. Select the radio Use the following IP Address
6. the content of your IP address
7. Select ok and so on
Tests
To test whether IP do you have for running well, do peritah ping:
Response ping successful:
root ~ root # ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56 (84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq = 1 TTL = 64 time = 0147 ms
64 bytes from 192.168.1.1: icmp_seq = 2 TTL = 64 time = 0119 ms
64 bytes from 192.168.1.1: icmp_seq = 3 TTL = 64 time = 0120 ms
64 bytes from 192.168.1.1: icmp_seq = 4 TTL = 64 time = 0195 ms
64 bytes from 192.168.1.1: icmp_seq = 5 TTL = 64 time = 0126 ms
--- 192.168.1.1 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 3996ms rtt min / avg / max / mdev = 0.119/0.141/0.195/0.030 ms
Naming fails if the ping does not show repon as above, one of the examples:
root ~ root # ping 192.168.1.4
PING 192.168.1.4 (192.168.1.4) 56 (84) bytes of data.
From 192.168.1.1 icmp_seq = 1 Destination Host Unreachable From 192.168.1.1 icmp_seq = 2 Destination Host Unreachable From 192.168.1.1 icmp_seq = 3 Destination Host Unreachable
--- 192.168.1.4 ping statistics ---
5 packets transmitted, 0 received, +3 errors, 100% packet loss, time 4026ms
, Pipe 3
You can ping to the IP network your colleagues to see if there is a connection between your PC to your PC network partners.
Penyetingan UTP cable with RJ 45 connectors
There are eight small cables in cable UTP but needed only four cable only. There are differences in the two cables to connect to a computer without a hub / switch, two-way computer dihubgunkan with crosslink as show in the picture below:
If refers to the color of the cable, you can use a table barikut:
Color cable PIN PIN
1 Orange + White 3
2 People 6
3 White + 1 green
4 Blue 4
5 White + 5 blue
6 Green 2
7 White, Brown 7
8 Brown 8
to cross pc to pc
but when we use the pc to the hub setingn cable that is in use.
Color cable PIN PIN
1 White 1 Orange +
2 People 2
3 White + green 3
4 Blue 4
5 White + 5 blue
6 Green 6
7 White, Brown 7
8 Brown 8
To test whether the relationship between the PC in the network, you can use the IP ping command the network. Usually, the success of the cable can be also seen from the light on the HUB or landcard up.